Choose a signal surge protector by matching the circuit’s operating voltage, continuous current, physical connection and transmission requirements, then check the stated protection levels for each path. A connector that fits is only one part of compatibility. A high discharge-current figure does not resolve a voltage, pin arrangement or signal-performance mismatch.
Unlike a single power-circuit specification, a signal connection may need several electrical and transmission fields considered together. The reviewed tables include nominal voltage Un, maximum continuous operating voltage Uc, nominal current IL, protection level Up, frequency or data-rate entries, insertion loss and interface descriptions. Not every model lists every field, so selection must remain specific to the exact device.
Define the interface before making a shortlist
Identify the circuit as analog signal, telephone/ISDN, digital signal, Ethernet/network, coaxial/RF, D-Sub or combined CCTV/video. Those groups describe different connection needs. Begin with the actual equipment interface and the conductors involved, rather than choosing a device because it appears in a broad “data protection” category.
Record the connector type, line count and any separate power connection. Include the pin arrangement or terminal drawing when available. The NTRJ45H-8L table, for example, describes one RJ45 port with eight lines. A terminal-connected analog device and an RJ45 device are not alternative housings for an otherwise identical circuit.
For a combined unit, identify each channel separately. CCTV-21M-48 has distinct RJ45 and power entries in its table. The data interface and power connection cannot be evaluated from a single voltage number, even though both appear in one enclosure.
| Circuit example | Fields that distinguish the enquiry | Example from the reviewed tables |
|---|---|---|
| Analog signal | Un, Uc, IL and terminal arrangement | NT-BE-24: 24 V, 30 V, 500 mA |
| Telephone/ISDN | Line voltage, line pair, current and frequency | NTPN-48: 48 V, 300 mA, >3 MHz |
| Digital signal | Voltage, line count, impedance and capacitance | NTBD-4L-180: per-line impedance 1.8 Ω |
| Network interface | Port/line arrangement and stated data rate | NTRJ45H-8L: one RJ45 port, eight lines, 300 Mbps |
| Coaxial interface | Connector, impedance and protection path | NT-BNC: BNC, 50 Ω |
| Combined CCTV | Data and power ratings independently | CCTV-21M-48: RJ45 plus terminal power connection |
Use this table to organize questions, not as a complete compatibility declaration. Application details absent from a model’s specification remain open questions. In particular, a connector name alone does not confirm every protocol or power-delivery arrangement that can use that connector.
Keep Un and Uc distinct
Un is the nominal operating voltage entry. Uc is the maximum continuous operating voltage entry. Keep both symbols in the comparison rather than shortening them to a single “voltage” column. AC and DC qualifiers are equally important when they appear.
NT-BE-24 lists Un 24 V and Uc 30 V. NTPN-48 lists Un 48 V and Uc 53 V. These examples show that a nominal value and a continuous limit are separate fields. Do not transfer the numerical difference between them to another product family as an assumed design margin.
NTBD-4L-180 illustrates why the AC/DC label must stay attached: its table states Uc 180 VDC / 127 V AC. NTRJ45H-8L lists Uc 6 VDC / 4 V AC. Omitting the qualifier would make the specification ambiguous and could conceal a circuit mismatch.
A complete request describes the normal circuit voltage and the relevant operating conditions, then asks whether the exact proposed model’s continuous rating fits. The product name is not a substitute for that check. If a table does not provide the needed voltage information, ask for clarification before using a similar model as a reference.
Check the continuous current separately from surge current
IL describes a continuous-current field in the reviewed signal tables. It must not be confused with In or Imax, which describe surge-current entries. A device with a kA surge rating can still have a much smaller permissible continuous signal-circuit current.
The examples differ substantially: NT-BE-24 lists IL 500 mA; NTPN-48 lists 300 mA; NTBD-4L-180 lists 0.75 A; NTRJ45H-8L lists 0.5 A. NT-N lists 20 A. Those differences belong to their individual interface designs and do not form a general current hierarchy for signal protectors.
Write the equipment circuit’s current requirement into the enquiry alongside the voltage. If the connection combines data and power, explain how power is carried. Do not infer support for a particular powered-interface arrangement from an RJ45 connector, a nominal voltage or a generic network description.
Preserve the original bandwidth units
The reviewed source tables mix frequency and data-rate terminology. NTPN-48 gives a maximum transmission frequency greater than 3 MHz. NTBD-4L-180 gives a line-to-PG cutoff frequency of 25.0 MHz. NTRJ45H-8L gives a bandwidth entry of 300 Mbps, while NT-N lists 3 Gbps.
These are not interchangeable units. A value in Mbps or Gbps should not be relabeled as MHz or GHz, and a frequency entry does not by itself guarantee a particular protocol throughput. Preserve the table’s value and unit, and request the missing performance information for the actual interface.
The same discipline applies to the NT-BE-24 entry, which states 10 Mbps, and CCTV-21M-48, which states a transmission rate of 30 Mbps. Neither value should be upgraded to a different network class or speed because the application name sounds similar.
When a procurement specification requires a protocol, cable category, operating-frequency range or powered interface, list that requirement explicitly. The available table may not establish it. A clear “needs confirmation” entry is more useful than converting an unfamiliar specification into a familiar but unsupported claim.
Review insertion loss, impedance and capacitance
Signal performance involves more than a headline transmission value. NT-BE-24 and NTRJ45H-8L list insertion loss ≤0.3 dB; NTPN-48 lists ≤1 dB. The reviewed NT-BNC and NT-N tables state 50 Ω impedance. Those entries should remain attached to their own models.
For NTBD-4L-180, the table reports per-line series impedance of 1.8 Ω, line-to-line capacitance ≤240 pF and line-to-PG capacitance ≤16 pF. The paths are different. Combining the two capacitance limits or dropping the path label would remove information needed to evaluate the proposed circuit.
Do not assume these limits apply over every frequency or under every operating condition when the table does not supply that scope. Request the relevant performance detail for the project. A table can identify a shortlist, but it should not be expanded into a test report that was never provided.
Read Up and discharge current by protection path
Signal tables commonly separate line-to-line and line-to-PG protection. For NT-BE-24, Up is ≤60 V line-to-line and ≤600 V line-to-PG. These describe different paths; the smaller number must not become the device’s sole unqualified protection level.
NTBD-4L-180 goes further by separating test conditions. It gives C2 line-to-line Up ≤270 V and C3 line-to-line Up ≤250 V, with distinct line-to-PG values. Keep the C2/C3 labels. Selecting the smallest figure from the table without its condition would create a misleading comparison.
NTRJ45H-8L also identifies a line-to-line Up of ≤30 V at 200 A and a line-to-PG Up of ≤500 V at 1.5 kA. Its per-line D1 Iimp is 0.5 kA and per-line C2 In is 1.5 kA. A purchaser should preserve both the per-line qualification and the test category rather than adding the lines together to invent a total rating.
Coaxial paths need similar care. NT-BNC lists C2 In 5 kA for line-to-shield and 10 kA for shield-to-PG. Its Up entries are also separated. Connector compatibility therefore does not remove the need to understand the intended shield and protective connection arrangement.
Evaluate both sides of a combined CCTV protector
For CCTV-21M-48, the RJ45 Uc entry is 8 V DC / 5.5 V AC, while the power Uc entry is 60 V AC. The table separately reports RJ45 line-to-line Up ≤30 V, RJ45 line-to-PG Up ≤500 V and power Up ≤200 V.
An enquiry for this type of device should describe the camera or interface connection and its power supply separately. It should not apply the power-channel rating to the data pins, or assume that a different camera voltage variant shares all the same values. Keep the exact model suffix in the request and ask for the applicable connection drawing.
Prepare an interface-specific selection brief
Provide the interface name, connector and pin arrangement, circuit voltage, continuous current, transmission requirement and proposed installation point. Add any required protection paths and the equipment-side limits available to the designer. Attach the equipment interface description if it resolves an ambiguity that a model name cannot.
Ask for clarification whenever a field is missing or its unit does not answer the project requirement. This includes protocol compatibility, performance over a required frequency range and the correct connection arrangement. Do not fill the gap from another series, even where two enclosures look identical.
Explore the signal and data range overview, or send the brief through Contact NONTIS. If your enquiry concerns a power circuit rather than an information interface, use How to Choose a Surge Protective Device for the separate class, continuous-voltage and discharge-duty workflow.
